top of page

Power Bank Safety in 2026: Recalls, China's Regulatory Response and What UL 2056 Means for Hardware Teams

Oct 30
15 min read

Updated: Nov 10

In brief: Roughly five million power banks have been recalled in the United States and China. In the 2025/26 recalls in China, both companies pointed at the battery cells, and the government responded with suspended certificates, ordered recalls, a rule for domestic flights and a new mandatory standard. UL 2056, the North American standard, is voluntary, but more buyers are asking for it. If you design or sell power banks, the part of the supply chain to control is the cell.

A power bank is a $20 accessory, and over the last two years it has drawn a lot of regulatory attention. The United States published 21 power bank recall notices between 2024 and September 2026, against 12 in all the years before. China suspended certificates, ordered recalls, set a rule for carrying power banks on domestic flights and published a new mandatory standard. In North America, UL 2056 went from an outline to a national standard, and Amazon changed what it expects from sellers.

We've put the numbers and the rules in one place, because the story is spread across CPSC notices, Chinese regulators' announcements and a standards body. Every figure has a source, and where the sources disagree we say so.

Key Findings

  • About five million power banks are covered by the recalls we could trace. That's roughly 4.1 million across 33 US notices since 2014, plus about 1.2 million in China in June 2025. The real global figure is higher, because Anker also recalled units in other markets and hasn't published a total.

  • US notices went from 2 in 2023 to 6 in 2024 and 11 in 2025. Four had been published in 2026 by 24 September.

  • In the two biggest recalls in China, Anker blamed a supplier's unapproved change to raw materials, and Romoss cited problems with incoming cell materials.

  • China's response was wide. It suspended certificates, ordered recalls, set a rule for domestic flights from 28 June 2025, and published a new mandatory standard, GB 47372-2026, which takes effect on 1 April 2027.

  • UL 2056 is voluntary, but OSHA listed it as a test standard in July 2025 and Amazon changed its testing rules for portable power supplies in December 2025.

  • The brand, the seller, the factory and the cell maker can be four different companies, which is why the cell supply chain is the part to watch.

About the Numbers

The US figures come from recall notices published by the US Consumer Product Safety Commission (CPSC), as compiled by Home Recall Watch, an independent site that draws on the CPSC's own data. It adds up the unit counts in each notice and counts a re-announced recall once. We checked the date and unit count of the six biggest notices against the CPSC's own pages.

The China figures come from company announcements and press reports, including CCTV coverage that we cite through TechNode and the South China Morning Post. The five-million figure adds two different kinds of source together, so it's an estimate rather than a count.

Power Bank Safety in Numbers: How Many Units Have Been Recalled?

Start with the United States, where the records are public. Home Recall Watch lists 33 CPSC power bank notices from 2014 to September 2026, covering at least 4.1 million units. Between them the notices state 707 incident reports and 45 injuries. Most of the recent ones describe the same hazard: a lithium-ion battery that can overheat and ignite. The six biggest notices were:

Date

Product

Units

12 June 2025

Anker PowerCore 10000 (model A1263)

1,158,000

20 June 2024

myCharge POWER HUB All-In-One, sold at Costco

567,000 

19 December 2024

Charmast power banks, sold on Amazon

488,000 

17 April 2025

Casely wireless portable power banks

  429,200 

13 March 2018

AmazonBasics portable power banks (made by Guoguang Electric)

260,000 

5 December 2025

INIU BI-B41 power banks, sold on Amazon

210,000 

The Casely recall was announced again on 16 April 2026 with the same unit count, so it's counted once. In the Anker notice, CPSC said the company had received 19 reports of fires and explosions.

In China, two recalls in June 2025 were the largest:


Date

Company

Units

16 June 2025

Romoss (three models)

491,745 

20 June 2025

Anker (seven models, China) 

More than 710,000 

Together they come to about 1.2 million units. Anker says it has started recalls in other markets too, including Japan, Europe and Southeast Asia, but as of July 2025 it hadn't published a global total.

Add the US total of 4.1 million to the 1.2 million from China and you get about 5.3 million. The two counts cover units sold in different markets, so nothing is counted twice. The figure is still low, because it leaves out Anker's recalls in other markets.

What Was Reported About the Causes

The 2025 recalls in China have the best-documented explanation, so we'll start there.

Anker said its production safeguards had helped it spot a possible problem with common lithium-ion cells from a single vendor, and it started a global recall. For the China recall, it said a supplier had made unapproved changes to raw materials. According to TechNode, that affected the separator in some cells and could lead to insulation failure and overheating. Anker also launched a Battery Safety Program covering supplier accountability, cell-level testing and end-to-end quality assurance. Romoss recalled three models and cited problems with incoming material in some of its battery cells.

At first, neither company named the supplier. According to the South China Morning Post, China's state broadcaster CCTV then identified Apex (Wuxi) Co., formerly Amprius (Wuxi), as the cell supplier for Romoss. China's market regulator suspended or revoked 74 China Compulsory Certification (CCC) certificates issued to the company, and its chairman said production would stop until the investigation finished. The company has said it makes its cells in line with regulations. SCMP also reports that Anker stopped sourcing from the supplier and began buying cells elsewhere.

Xiaomi, Ugreen and Baseus were reported to have used cells from the same supplier, and several of them had certificates suspended in the same period. 

How Chinese Authorities Responded

China worked on four fronts at once: certification, recalls, flights and standards. This is how it unfolded.

Date 


What happened

Source

2023 to 2024

Power banks and lithium-ion batteries are brought under China Compulsory Certification (CCC), announced in 2023 and applied to products sold in China from 1 August 2024

Chinese compliance guides

Early June 2025

Certificates for power banks from several brands, including Romoss, Anker, Baseus and Ugreen, show as suspended in the national certification database

Shanghai Metals Market, citing the regulator's database

Mid-June 2025

Several Beijing universities tell students to stop using certain Romoss power banks after reports of incidents 

SCMP, AsianFin 

16 and 20 June 2025 

Romoss and Anker announce recalls in China 

TechNode

Mid to late June 2025 

The market regulator, the State Administration for Market Regulation (SAMR), suspends or revokes 74 certificates held by the cell supplier

SCMP

28 June 2025

The Civil Aviation Administration of China (CAAC) bars power banks without a clear CCC mark, and recalled models or batches, from domestic flights 

TechNode, other reports

September 2025

SAMR says it has directed Romoss, Anker and Xiaomi to recall power banks and set up a supervisory task force, with inspections in 11 provinces and municipalities 

Global Times

1 March 2026

Newly certified power banks must carry a traceability QR code next to the CCC mark. From 1 March 2027 this applies to all certified products in the pilot

CNCA announcement of 23 December 2025, via CAICT; China-certification.com 

31 March 2026

The mandatory standard GB 47372-2026 is published, taking effect on 1 April 2027

By early July 2025, CCTV had reported 15 incidents that year in which passengers' power banks caught fire or gave off smoke on flights. The aviation rule covers domestic flights within mainland China. It applies to power banks with no CCC mark, a mark that can't be read, or a model or batch that has been recalled.

In September 2025, SAMR said Romoss had recalled 167,000 units, Anker 565,000 and Xiaomi 17,000, and that the three were required to recall more than 1.35 million in total. It also said it had reviewed power banks and lithium batteries certified under CCC.

GB 47372-2026 is described as China's first dedicated mandatory national standard for power banks. According to the China Academy of Information and Communications Technology, the Ministry of Industry and Information Technology led its drafting. It tightens protection against abuse such as high temperature, overcharging and extrusion, adds a check for lithium plating after cyclic ageing, and sets requirements for raw materials and production process control. CCC will use it alongside GB 31241 and GB 4943.1, under new implementation rules numbered CNCA-C09-02:2026. There's a 12-month transition, and the standard takes full effect on 1 April 2027.


Who Is Named on a Recall? Brand, Seller, Importer and Cell Maker

The recall notices make one thing clear: the company named on a recall isn't always the one that made the product. A few CPSC notice titles show it:

  • "Fantasia Trading Recalls Anker Power Banks" (2023)

  • "Distributed by Waymeet" (ESR HaloLock wireless power banks, 2025)

  • "Imported by Tomauri" (iStore magnetic wireless power banks, 2025)

  • "Sold on Amazon.com by Shenzhen Baseus Technology" (2025)

  • "Manufactured by U2O Global" (iWALK wireless power banks, 2025)

Home Recall Watch makes the same point: brand-name products are often made by another firm, so one recall can span several brands. The 2025 recalls in China added another layer. The names on the products were Romoss and Anker, but the cells came from a supplier that several brands shared. So there can be four companies to think about: the brand, the seller or importer, the factory that built the product, and the company that made the cell. A change at the last of those can reach all the others. What Is UL 2056? UL 2056 is the Standard for Safety for Power Banks, published by UL Standards & Engagement. It applies to what it calls power banks, also known as portable USB chargers: standalone devices that hold a battery and use it to power low-voltage electronic devices. Its stated purpose is to reduce the risk of fire or explosion.

It tests the finished product, not only the parts inside. A cell can pass its own standard and a battery pack can pass another, but the power bank still has to be evaluated as a whole: the cell, the protection electronics, the enclosure, the ports, and how they behave together when something goes wrong.

How UL 2056 got here

Date

What happened

Source

13 October 2015 

UL launches its first dedicated testing and certification service for power banks, tested to UL 2056, at the Hong Kong Electronics Fair 

UL press release 

20 August 2020

Edition 3 of the Outline of Investigation for Safety of Lithium-ion Power Banks is published 

UL Standards store 

2023

CPSC staff send comments on the draft first-edition standard. CPSC, Health Canada and Mexico's consumer agency Profeco had written to UL in February 2023 offering to contribute 

CPSC letter 

22 October 2024

A revision updates the enclosure requirements (clauses 4.3 and 6.1.4) 

UL Standards store 

8 February 2025

A revision updates the enclosure requirements (clauses 4.3 and 6.1.4) 

UL Standards store 

24 July 2025

OSHA publishes its decision to add UL 2056 to the list of appropriate test standards for its Nationally Recognized Testing Laboratory (NRTL) program, and expands UL's recognition to include it 

Federal Register 

30 June 2026

A further revision is approved by ANSI and the Standards Council of Canada

UL Standards store 

What it covers


Clause 1 of the current edition sets the scope by power characteristics:

  • Input from an isolated DC source rated up to 60 Vdc, or from AC mains through a direct plug-in construction

  • DC output rated up to 60 Vdc

  • A watt-hour rating of no more than 100 Wh

  • Primary or secondary batteries

  • Products with integral photovoltaic cells

Anything within the scope of UL 2743, the Standard for Portable Power Packs, is excluded (clause 1.5). If you're building a jump starter or a portable power station, UL 2743 applies instead.



Outline of Investigation (Edition 3, 2020) 

ANSI/CAN/UL 2056 (Edition 1, 2024 onwards) 

Battery type 

Lithium-ion 

Primary or secondary batteries 

Maximum voltage 

20 Vdc input and output 

60 Vdc input and output 

Energy limit 

None stated in the scope text we found 

100 Wh 

AC input

Not mentioned 

Direct plug-in construction covered 

Status

UL outline

ANSI and Standards Council of Canada approved standard 

What the tests look like

UL sells the standard and doesn't publish the test methods. UL Solutions describes it as covering overcharge and discharge protection, short-circuit and overload tests, drop and impact resistance, and thermal safety. The summary of changes in the June 2026 revision names specific clauses, which gives a good idea of what's inside:

  • Flammability of internal parts (6.1.5)

  • The short-circuit of output port test (12.3)

  • The abnormal charging of the battery test (13.2 and 13.4)

  • The temperature test and battery management system (BMS) verification (an exception to 16.5)

  • The flexing force test (Figure 23.1)

  • The mold stress relief test (24.1)

  • Direct plug-in construction (6.7.1(c))

  • The limits on cell temperatures used across several electrical tests

The standards it depends on

UL 2056 refers to 20 other UL standards. The ones that matter most for a bill of materials are UL 1642 (lithium cells), UL 62133-2 (portable sealed secondary lithium cells and batteries), UL 2054 and UL 62133-1 (other chemistries), UL 62368-1 (audio, video and information technology equipment), UL 94 and UL 746C (plastics), UL 796 (printed wiring boards), UL 248-14 (supplemental fuses), UL 60691 (thermal-links), UL 1434 (thermistor-type devices), UL 60730-1 (automatic electrical controls), UL 1977 (connectors) and UL 2738 (induction power transmitters and receivers).

A 2023 draft of the first edition, published with CPSC staff comments, set out the cell requirement like this: a lithium cell has to comply with UL 1642 or UL 62133-2. Test labs describe a similar rule in their summaries. Check it against the published text of the current edition.

Is UL 2056 mandatory?

Not as a standard. ComplianceGate's review of US power bank requirements found no rule that makes a UL 2056 test report compulsory. The pressure comes from where the product is sold.

OSHA added UL 2056 to the NRTL Program's list of appropriate test standards in July 2025 and expanded UL's recognition to cover it. UL Solutions says it was the first NRTL to apply the standard and, at the time of its article, the only one offering UL 2056 certification.

Amazon's Seller Central guidance has listed UL 2056 certification as one route for selling power banks, and has asked for test reports from an ISO/IEC 17025-accredited laboratory. In December 2025, Amazon announced new testing requirements for portable power supplies on its US and Canadian stores, which include power banks. For affected listings, sellers have to work with an approved third-party testing, inspection and certification (TIC) provider, either to test the product or to validate existing test documents. Check the current rules in Seller Central before you plan. CPSC staff contributed comments to the draft standard.

UL 2056 and China's Rules Compared



UL 2056 

China CCC 

Where it applies 

North America 

China

Status 

Voluntary as a standard, asked for by marketplaces and retailers 

Mandatory for power banks sold in China, and a condition for carrying power banks on domestic flights 

Basis 


ANSI/CAN/UL 2056, published by UL Standards & Engagement 

GB 31241 and GB 4943.1, with GB 47372-2026 added from 1 April 2027 

Latest change

Revision approved 30 June 2026

GB 47372-2026 published 31 March 2026

The two are separate systems, and one doesn't stand in for the other. A power bank sold in both markets needs evidence for each. What UL 2056 Does Not Replace

  • UN 38.3 is the transport test for lithium batteries. Power banks must meet it to ship, and Amazon asks sellers for the test summary.

  • Radio rules apply separately if the power bank has wireless charging or another radio function, for example FCC Part 15 in the United States.

  • Other markets have their own routes. The EU, the UK and China are all different.

  • The cell's own certification still applies to the parts inside the product.

What This Means for a Hardware Team

What follows is our own view of the lessons, not part of any standard.

Know who makes your cells

In the 2025 recalls in China, the explanation was a change to raw materials that the brands didn't control. So ask for the certificate covering the exact cell model, the test report behind it, and a written promise to tell you before the chemistry, the plant or the materials change.

Put change notification in the contract

A promise in an email is easy to forget. Write it into the supply agreement, and say what counts as a change: materials, process, plant, and the suppliers of the separator and electrolyte.

Trace by lot, down to the cell

If a cell lot is flagged later, the first question is which finished units used it. Record cell lot numbers against finished-product serial numbers at the factory. China now requires a traceability QR code on newly certified power banks, and the same records are useful in any market.

Plan a second source

Anker moved to other suppliers after the recalls. Qualifying a second cell takes time, so decide early which designs can take an alternative and which can't.

Treat a test report as tied to the product you tested

ComplianceGate points out that a report is valid only for the specific power bank that was tested. That makes change control part of compliance. If you swap the cell, the protection IC, the enclosure plastic or a connector after testing, you may need to retest. It's far easier to ask the lab before you make the change than after.

Design with the test in mind

The output-port short-circuit test, the abnormal charging test and the temperature and BMS verification all depend on how the BMS and protection components behave under fault conditions. Ask the lab to review the schematic and the protection design before you build samples.

Keep the paperwork ready

Expect to be asked for cell certificates, material data sheets, certificates for fuses and thermal links, the schematic, the bill of materials and the label artwork. If the supplier file is complete before testing starts, you save weeks of back and forth.

Check that the factory builds what was tested

A report covers the samples the lab received. The units that leave the line should match them, which comes down to supplier control, incoming checks and consistent assembly.

If you sell in China

Note the dates. GB 47372-2026 takes full effect on 1 April 2027, and there's a transition period until then.

Questions to put to your lab

  • Which edition and revision of UL 2056 will the report be issued against?

  • Does the current edition include a capacity check, and how should we state the rated capacity?

  • Which changes after testing would need a re-evaluation?

  • Will the report be accepted by our retailer or marketplace, including through their TIC process?

  • Can you review the schematic, BMS design and bill of materials before we build samples?

Questions to put to your cell supplier

  • Which UL 1642 or UL 62133-2 certificate covers this exact cell model?

  • What are the specified charge and discharge limits and operating temperatures?

  • How and when will you tell us about changes to materials, process or plant?

  • Can you give us lot-level traceability for the cells we receive?


Conclusion

Looking at 2024 to 2026 together, this is when power banks stopped being treated as a minor accessory. US recalls rose to 11 notices in 2025. China answered with certificate suspensions, ordered recalls, a rule for domestic flights and a new mandatory standard. In North America, UL 2056 became a national standard and started to show up in federal and marketplace requirements.

What stands out to us is where the trouble was traced. The cell is the part of a power bank that most brands buy in, and the 2025 recalls showed how far a change at the cell maker can travel. Teams that know their cell supplier, write change notice into contracts, trace lots to finished units and show their designs to a lab early will find UL 2056 and the new Chinese rules much easier to deal with.

If you're designing a power bank and want to talk through the cell, the bill of materials or the route to testing, we'd be glad to help. This article is general information, not legal or certification advice. Standards and marketplace requirements change, so use the current published text of each standard for any decision.

FAQ

How many power banks have been recalled? About five million, based on the recalls we could trace. Roughly 4.1 million are across 33 US notices published between 2014 and September 2026, and about 1.2 million were recalled in China in June 2025. The global figure is higher, because Anker also recalled units in other markets and hasn't published a total.

Why were power banks recalled in China in 2025? Both Romoss and Anker pointed to battery cells. Anker said a supplier's unapproved changes to raw materials affected the separator in some cells, and Romoss cited problems with incoming material in some cells.

What did the Chinese government do? China's market regulator suspended or revoked certificates, including 74 held by the cell supplier that CCTV named. It later ordered recalls and set up a supervisory task force. The civil aviation authority has required a clear CCC mark on power banks carried on domestic flights since 28 June 2025, and a new mandatory standard, GB 47372-2026, was published on 31 March 2026.

Can I fly in China with a power bank that has no CCC mark? Not on domestic flights within mainland China. Since 28 June 2025, power banks with no CCC mark, an unclear mark, or a recalled model or batch have not been allowed on those flights.

What is GB 47372-2026? It's China's first dedicated mandatory national standard for power banks. It was published on 31 March 2026 and takes effect on 1 April 2027, after a 12-month transition. CCC certification will use it as an additional basis.

What is UL 2056? UL 2056 is the Standard for Safety for Power Banks. It covers standalone devices that use a battery to power low-voltage electronic devices, and it aims to reduce the risk of fire or explosion. The first edition was published on 22 October 2024 as ANSI/CAN/UL 2056.

Is UL 2056 mandatory? Not as a standard. In practice, marketplaces such as Amazon and some retailers ask for evidence of compliance, and OSHA added UL 2056 to its list of appropriate test standards in 2025.

What is the difference between UL 2056 and the CCC mark? UL 2056 is a North American standard that is voluntary as a standard. CCC is China's compulsory certification system. They are separate, and a product sold in both markets needs evidence for each.

Does UL 2056 replace UN 38.3? No. UN 38.3 is the transport test for lithium batteries. Power banks need it to ship, and it's separate from UL 2056.

Which standards apply to the cells inside a power bank? UL 2056 refers to UL 1642 and UL 62133-2 for lithium cells and batteries. UL 2056 itself evaluates the finished power bank.

How can a brand protect itself from changes at the cell supplier? Name the cell model and plant in the supply agreement, require written notice of any change in materials, process or plant, record cell lot numbers against finished-product serial numbers, and qualify a second source where the design allows.

When was UL 2056 last updated? The first edition was published on 22 October 2024. It was revised on 18 February 2025 and again on 30 June 2026.



 
 
 

Comments


©2026 by Ardencraft Technology

bottom of page